Construction Of Car Touch Intruder Alarm
Table Of Contents
- TABLE OF CONTENTTitle Page ...…………………………………………………………………….iCertification…………………………………………………………………….iiDedication ……………………………………………………………………...iiiAcknowledgement …………………………………………………………….. ivAbstract ………………………………………………………………………….vTable of content ………………………………………………………………...viList of Symbols ………………………………………………………………. vii
Chapter ONE
INTRODUCTION
-
- 1.1 Background of study……………………………………………………
- 11.2 Aims and objectives…………………………………………………… 3
Chapter TWO
LITERATURE REVIEW
- ……………………………………….4
Chapter THREE
RESEARCH METHODOLOGY
- Specification and operation of system component
- 3.1 Description of NE55 Timer…………………………………………….12
- 3.2 Description of Resistor……………………………………………….
- 143.3 Description of Capacitor……………………………………………..
- 163.4 Description of Diode…………………………………………………
- 273.5 Description of Transformer ……………………………………………
- 323.6 Description of Loud Speaker and Buzzer………………………………
- 413.7 Description of Transistor……………………………………………….
- 433.8 Description of L.E.D………………………………………………….. 47
Chapter FOUR
DATA PRESENTATION AND ANALYSIS
- Operation of system and its circuit and block diagram4.1 Operation of circuit ………………………………………………… …
- 554.2 The circuit diagram………………………………………………….. ..
- 574.3 The block diagram………………………………………………………58
Chapter FIVE
SUMMARY, CONCLUSION AND RECOMMENDATIONS
- Construction, Testing and Packaging5.1 Values of components………………………………………………….
- 595.2 Assembly………………………………………………………………
- 605.3 A schematic diagram of the finished work…………………………….63 CHAPTER SIX: Conclusion and Recommendation6.1 Conclusion ………………………………………………………….. .
- 646.2 Recommendation …………………………………. …. ……… .….
- 656.3 Observations ………………………………………………………..
- 666.4 Dificulties…………………………………………………….. …
- 576.5 References…………………………………………………. …………68
Thesis Abstract
ABSTRACT
The main objective of this project was to ensure a proper security to car being parked in garage against theft or an intruder. The circuit uses three NE555 timers; one of the NE555 was wired as a monostable oscillator and remaining two were wired as tone generator and amplified to obtain a maximum audible sound. However, pin 2 of the first NE555 was used as sensor part .When pin 2 has contact with human body or hand it will activate the IC1 which will also bias transistor and this transistor was wired in a way that once it is powered it will close circuit thereby passing a negative supply voltage to tone generator circuit and outputted out through a loud speaker or buzzer.
This device functions as a major security device against car-theft as stated above. It is an electronic device that is connected to the battery of the car it is being installed in and gets activated when the car engine is switched off and the car stationed at a place. The device is not seen but, it has an indicator light which shows that the alarm has been activated. When the body of the car is touched by human hand, it sends a negative signal to the device which needs a negative pulse to get activated; it sends this negative from the human hand to the tone generator IC which triggers the alarm.
Thesis Overview
<p> </p><p><strong> INTRODUCTION</strong></p><p><strong>1.1. </strong><strong>Background of the Study</strong></p><p><strong> </strong> The first car alarm was a primitive contraption that utilized a bell or horn connected to the drive shaft. It was created by an unnamed Nebraska inventor in June 20th, 1920. It utilizes the drive shaft to operate its own bell or horn signal when the car is properly moved. This is just a little talk on a car alarm but not a car touch intruder alarm which is a modern, more advanced, and more reliable type of car alarm.</p><p> This car touch sensitive alarm project consist of three NE555 timer IC, the first NE555 was wired as monostable multi-vibrator and the remaining two were wired as tone generator. When the sensor is touch or has contact with human hand perhaps body, IC1 is triggered at its pin 2 and output pin 3 goes high for a time period previously set by the values of R4 (10M) and Q1 (transistor) was bias via R3 and this transistor is in such a way that once it was biased it will supply a negative voltage to tone generator thereby making two NE555 timer which was know as (tone generator) to oscillate to make a bell sound through the buzzer. The tone generators are configured as an astable multi-vibrator whose oscillation frequency can be varied with the help of PR1 and PR2. By adjusting the values of PR1 and PR2, modifications on the tone are possible.</p><p>The reset button is used to set or open circuit the system back to its initial stage. The system is powered with 12V power supply voltage.</p><p>The first chapter of this project is narrating on the introduction, the concept of the system and also the aims and objective. Chapter two is all about literature review. Chapter three talks about specification and operation of system component. Chapter four is operation of system. Chapter five is about construction, testing and packaging. Chapter six is conclusion, observation, recommendation and References.</p> <br><p></p>Blazingprojects Mobile App
📚 Over 50,000 Research Thesis
📱 100% Offline: No internet needed
📝 Over 98 Departments
🔍 Thesis-to-Journal Publication
🎓 Undergraduate/Postgraduate Thesis
📥 Instant Whatsapp/Email Delivery
Related Research
A Global Expectation Framework for Strategic Diplomacy under Multipolarity...
This research explores how global leaders and major powers coordinate diplomatic behavior in a world where power is distributed among several influential region...
A Framework for Circularity-Oriented Catalytic Process Design in Industry...
This research explores how catalytic processes in industry can be redesigned to support circular economy principles, reducing waste, conserving resources, and e...
A Dynamic Resilience-Based Framework for HR Transformation and Outcomes...
This research explores how organizations can make HR practices more resilient and dynamic in the face of rapid changes such as technology disruption, demographi...
A Farm-Province Adaptive Resilience Framework for Rural Households...
This research investigates how rural households connected to both farming and provincial markets build resilience to shocks and stresses. It addresses the gap b...
A Framework for Integrating Isotopic Signatures in Sedimentary Basin Thermochronolog...
This research explores how isotopic signatures can be integrated into thermochronology studies of sedimentary basins to better understand their thermal historie...
Cadre théorique pour l’évaluation éthique des IA en entreprise ...
This research explores how to build and apply a theoretical framework for evaluating the ethics of artificial intelligence (AI) used in business settings. It as...
A Resilience-Framing Framework for Urban Water–Energy–Waste Nexus Governance...
The research topic explores how cities can manage the interconnected systems of water, energy, and waste more effectively by using a resilience-framing framewor...
A Resilience-Framing Framework for Urban Environmental Management Systems...
This research explores a resilience-framing framework for urban environmental management systems, focusing on how cities plan for, respond to, and learn from en...
A Pragmatic-Narrative Alignment Model for Multilingual Interaction...
The research investigates how speakers manage meaning across languages in multilingual settings by proposing a Pragmatic-Narrative Alignment Model. It aims to e...
