The refurbishment of temperature control apparatus

Thesis Overview

<p> </p><p>1.0 &nbsp; &nbsp; &nbsp; <strong>Introduction</strong></p><p>Armfield temperature control appara [tus is a pilot plant scale apparatus for the study of heat transfer, process control fluid mechanism and thermodynamics by chemical Engineering students in various institutions of higher learning.</p><p>&nbsp;</p><p>The apparatus consists of two heaters, with voltage between 220-240 and 6kw of power. The heaters has thermostatic range from 380C-82C0, heat transfer area (A) of the heat exchanger is 0.64m2 (0.059fts2) ALFA-LAVAL. Four thermo walls, each fitted at the inlet and outlet points on the heat exchanger for insertion of thermometers for temperature measurement. It has a sump tank of capacity of 70 litres, three flow meters (Rotameters), two of variable area type, a pump of power 0.23kw and capacity of 55litres/min at 1.5m and 9 litres/min at 6m. a control valve (air regulator) of ½ inch, PID (Honey well) controller, two pen chart recorder, temperature sensor, electronic controller etc. as the name applies it is used to control or measure temperature.</p><p>In industries in order to avoid wastes during production of goods, even in pilot plant where production of good are in small scale, there is need for control system which gives more stable (Uniform) process and higher quality products. Certain variables like temperature applied to fluid or rather dictated from body, fluid flow rate, pressure etc which causes loss of valuable materials during production. Some of the above mentioned variable can be corrected using temperature control apparatus.</p><p>Heat exchange is one of the most frequent operations mainly in process industries. A large number of processes proceed at a much faster rate as the temperature is raised and it is economically advantageous to use as high a temperature as possible. Chemical reaction rates are approximately doubled for every 100 rise in temperature.</p><p>Chemical reactions are frequently exothermic, however, and it may well be necessary to remove heat through a heat exchanger rather than supply it inorder to avoid a catastrophic temperature rise. Thus, to balance the requirements of maximum efficiency and complete control over the process may require the very close regulation of the temperature.</p><p>The pilot plant temperature control apparatus is designed to show the working of a heat exchanger and to permit a series of experiments to be performed with it. Water is both the process fluid and the heating fluid, the rate of flow may be set up to show how flow control may be obtained in various ways.</p><p><strong>1.1 &nbsp; &nbsp; &nbsp; AIMS AND OBJECTIVES OF THE REFURBISHMENT</strong></p><p>Refurbishment is to keep the apparatus in top operating condition through repairs, maintenance and servicing of parts of the apparatus. Through the refurbishment it increase the workability of the apparatus (equipment) the degree of accuracy and precision as well the sensitivity of the equipment. It improves the performance of the equipment, maximize efficiency and bring error to minimum.</p><p>Through the maintenance or refurbishment of the equipment, quantity/quality control, cost effectiveness, strength of material and prolonged apparatus/plant life span can be obtained.</p><p><strong>1.2 &nbsp; &nbsp; &nbsp; SCOPE</strong></p><p>This involves detecting the faulty components of the temperature control apparatus and the repairing which includes general servicing, flushing of the sump tank. To reduce fouling, scraping off the corroded parts, filling of the leaking parts with filler and painting of the sump tank. Ensuring that there would be no leakage either by values or pipes when running the apparatus and the efficiency of the circulating pump.</p><p>At the end, it is expected that he pilot plant temperature control apparatus will be in top operating condition. &nbsp;</p><p>&nbsp; &nbsp; <strong>TERMS AND CONDITIONS</strong></p><p><strong>Using our service is LEGAL and IS NOT prohibited by any university/college policies</strong></p><p><strong>You are allowed to use the original model papers you will receive in the following ways:</strong></p><p><strong>1. As a source for additional understanding of the subject</strong></p><p><strong>2. As a source for ideas for your own research (if properly referenced)</strong></p><p><strong>3. For PROPER paraphrasing (see your university definition of plagiarism and acceptable paraphrase)</strong></p><p><strong>4. Direct citing (if referenced properly)</strong></p> <br><p></p>